Équivalents:
CIMR-VMW25P5
Tension: 230 V
Série: VS626-VM3
CENTRE DE SERVICE AUTORISÉ YASKAWA AU CANADA
CIMR-VMS25P5 Yaskawa
Numéro de pièce du fabricant :
123-456-789
Manufacturer part number :
CIMR-VMS25P5
CIMR-VMS25P5 Yaskawa
9 KVA , Serial VS626-VM3
Varispeed-626VM3 drives (VS-626VM3) combine a compact, high speed AC spindle drive motor with a digital vector-controlled, high performance transistor inverter (controller) with regenerative function.
The VS-626VM3 Drives has highly reliable adjustable speed AC spindle motor drives for NC machine tools such as machining centers and lathes, and manufacturing facilities such as transfer machines and testers. They assure exceptional stability, even at high speeds under severe operating conditions.
The features of the VS-626VM3 are as follows:
- 800 r/min max and constant power range (1:5.3) (for 7.5 kW or below)
- Constant power (1:12) with winding selection (No speed change gear required)
- Two series for power voltages of 200V and 400V
- Precise setup of position and speed by fully digitalized control
- Compact and lightweight
Error codes
Error code : F-000
Protective Function : Winding Selection Failure
Explanation : Windings were not selected within set time.
Error code: F-001
Protective Function: Emergency Stop Failure
Explanation: Operation was not stopped within 10 seconds after emergency stop was commanded.
Error code: F-100
Protective Function: Inverter Output Overcurrent
Explanation: Output current exceeded set overcurrent value.
Error code: F-200
Protective Function: Inverter Internal MC Operation Failure
Explanation: The magnetic contactor in the input block is not functioning.
Error code: F-201
Protective Function: MCCB Trip
Explanation: The MCCB in the input block tripped.
Error code: F-300
Protective Function: Inverter Input Overcurrent
Explanation: Input current exceeded set overcurrent value.
Error code: F-400
Protective Function: Inverter Overvoltage
Explanation: Inverter DC bus voltage exceeded set overvoltage value.
Error code: F-500
Protective Function: Motor Overspeed
Explanation: Motor speed exceeded 120% of max. set speed.
Error code: F-600
Protective Function: Power Voltage Error 1
Explanation: Synchronous power signal is lost (at power-ON).
Error code: F-601
Protective Function: Power Frequency Error 1
Explanation: Whether 50 Hz or 60 Hz cannot be determined (at power-ON).
Error code: F-602
Protective Function: Power Voltage Error 2
Explanation: Low-Voltage (85% or lower), momentary power loss (for 0.02 second or longer), or open phase.
Error code: F-603
Protective Function: Power Frequency Error 2
Explanation: Excess power frequency deviations (Deviation is 5% or the frequency or greater)
Error code: F-604
Protective Function: Power Voltage Error 3
Explanation: Low-Voltage of control power source (175 VAC or lower) or power loss.
Error code: F-700
Protective Function: Inverter Output Overload
Explanation: Output current of 120% of 30-minute rating flowed for one minute or longer.
Error code: F-701
Protective Function: Inverter Input Overloard
Explanation: Input current of 120% or 30-minute rating flowed for one minute or longer.
Error code: F-800
Protective Function: Excess Speed Deviation
Explanation: Speed rose to 120% of commanded value or greater, or dropped to 50% or lower.
Error code: F-900
Protective Function: Motor Thermal Error 1
Explanation: Motor temperature exceeded upper limit (Minor Failure)
Error code: F-901
Protective Function: Motor Thermal Error 2
Explanation: Motor temperature over upper limit continued for four minutes or longer.
Error code: F-902
Protective Function: Motor Thermal Error 3
Explanation: Break in wire occurred in the motor temperature detection thermistor. (Detected at -10 degree Celcius or less)
Error code: F-903
Protective Function: Heat Sink Thermal Error 1
Explanation: Heat sink temperature exceeded upper limit (Minor Failure)
Error code: F-904
Protective Function: Heat Sink Thermal Error 2
Explanation: Heat sink temperature over upper limit continued for one minute or longer.
Error code: F-905
Protective Function: Heat Sink Thermal Error 3
Explanation: Break in wire occurred in the heat sink temperature detection thermistor. (Detected at -10 degree Celcius or less)
Error code: F-906
Protective Function: Control Panel Thermal Error 1
Explanation: Panel internal temperature exceeded +55 degree Celsius (Minor Failure)
Error code: F-907
Protective Function: Control Panel Thermal Error 2
Explanation: Panel internal temperature exceeded +60 degree Celsius